Brick Paver Installation & Edging



Staging of product

Most paver jobs will differ depending on gain access to, website conditions, job size and of course, the weather. Cautious factor to consider needs to be taken to figure out the time to begin the paver installation.

The supervisor or job supervisor need to constantly have the materials (sand/ pavers) distributed around the job site for efficient and easy installations. Paver pallets/bundles need to be placed in a manner not to interfere with the paver installation. The correct pallet/bundle placement can make the actual project installation much easier and quicker by minimizing the general labor of handling the product.

Brick paver patterns

Pavers can be placed in several patterns depending upon their shape. Each paver shape will typically have several different hatch patterns that are supplied by the producer.

Specialists need to take into factor to consider the traffic weight loads on their paver jobs. In most applications worldwide, it has actually been shown that pavers laid in a herringbone pattern have actually performed effectively.

Pavers that are 60 mm (2 - 3/8 in) thickness are suitable for pedestrian applications. Pavers that are going to be utilized in commercial or commercial applications need to be 80 mm (3 - 1/8 in) in thickness.

Reference/starting point for brick paver installation

There are a variety of conditions that determine the beginning point of a paver task.

When beginning to install pavers it is best to snap a real straight chalk line on the surface of the bedding sand or pull a real straight string line above the surface of the bedding sand at the ended up elevation of the pavers This will help as a guide for keeping straight joint lines and will also allow the installer to make changes in the alignment of the pavers.

Structures and concrete curbing are usually not straight and should not be utilized for developing straight joint lines. The use of string lines is vital to determine the true straightness of the edge also. As the paver installation progresses, the string lines will assist decrease the requirement for little trim pieces.

Joint width in between pavers ought to be in between 1/16 and 3/16 in (2 and 5 mm ). There are some pavers with spacer bars on their sides. These will keep a minimum joint width and allow the bed linen and jointing sand to get in between each paver. Pavers with spacer bars are normally not laid in snug against each other considering that a string line will supply consistent joint spacing.

Installation of brick pavers.

One of the most commonly used techniques for the installation of pavers is hand installation of each paver. It is best to set up a single row of pavers along among the true straight lines that you have pulled or above the bedding sand. This will provide you a straight and real line off which to work. Once this row is established, you can continue to work outside into the field with the rest of the pavers. Constantly make certain to periodically check your joint lines to make sure they are real and straight. If not, adjustments to the pavers can be made as you continue setting up. Pavers needs to be set up hand tight. The very best approach is to put a paver against another one and let it slide down into the bedding sand. Do not kick or tap the pavers into location as this can toss your lines out of real straightness.

When setting up pavers on a high grade, they need to be set up at the base of the grade going uphill. This will avoid the pavers from sneaking as they are being laid.

On big business and commercial applications, hand laying pavers would not be cost effective due to the labor strength. The very best method for setting up pavers on Patio Pavers West Palm Beach large jobs is to install them mechanically. The use of a mechanical laying machine can install approximately 6000 - 7000 sq ft a day. There are a couple items a contractor need to think about before installing pavers mechanically:

1.) Mechanical installers are just capable of installing pavers in specific patterns.

2.) The professional should ensure that the manufacturer can manufacturing and bundling pavers in the wanted pattern on the pallets for simple mechanical installation.

3.) Specialists might come across a color mixing situation coming off the packages of pavers Poor color mixing could result in an irregular looking installation. The majority of makers are consistent with color mixing on each package of pavers, but it is the contractor's duty to ensure proper mixing in the field.

Cutting treatments for brick pavers.

Professionals generally have 2 ways of cutting pavers. Pavers are cut either by 1). A double bladed guillotine or by 2). A gas powered cut off saw or brick saw which is equipped with a diamond blade. The diamond blade cut-off saw or brick saw will supply a much cleaner and more accurate cut. Most brick saws will have a pipe attachment on them which will permit the operator to cut the pavers wet. When cutting pavers wet, it will assist minimize dust and will lengthen the diamond blades life also. The operator of the brick saw ought to always cut the pavers far from the surface area of the paver field when cutting wet, due to that the pavers will produce a slurry that will stain the paver surface. Pavers that are cut must not fit tight, sufficient spacing must be available for jointing sand.

The brick saw operator should always wear the correct security that is needed for running a saw, such as eye, ear, respiratory and hand defense ).

Edging types

Edge restraints play a major role in the general success of an interlocking pavement installation Edging restraints eliminate lateral motion of the pavers and hold the pavers firmly together. Especially at the external perimeter of the paver application, without an edging restraint, your task is guaranteed to stop working gradually.

Generally made edge restraints are the most commonly utilized by contractors. Made edging restraints can range from, plastic edging, steel and aluminum, lumbers or precast concrete and stone.

Edging installation.

This might result in the migration of the bedding sand and ultimate lateral motion of the pavers. If there is a possibility of losing bedding sand in between the pavers and the edge restraint, then geo textile material is recommended. When a space in between the pavers and the edging exceeds 3/8" (10mm), then the area needs to be filled with cut pavers.

Compaction of brick pavers.

After installation, the pavers need to be compressed. The whole area that is to be compacted need to be swept clean of any foreign items and particles that can trigger scratching or scuffing on the surface of the pavers.

It is necessary to have a compactor that can exert between 3000lbs. And 5000 pounds. Of centrifugal compaction force. In addition, it is important that the first compaction occurs prior to any jointing sand has been applied to the pavers. If jointing sand is applied to the pavers prior to compaction happens, this can cause a bridging issue and will not allow the joints to be totally filled with jointing sand. This can also prevent the pavers from being appropriately set into the bed linen sand.

When compacting the pavers, it is advised that you make a minimum of two passes in different directions throughout the pavers. This will permit the pavers to be effectively set in the bedding sand and will force the bed linen sand up into the joints from the bottom of the pavers.

The compaction of the pavers is really critical to the final performance of the pavers. Failure to do appropriate compaction can lead to contortions and pavement failure in time.


Paver pallets/bundles must be positioned in a way not to interfere with the paver installation. One of the most widely used techniques for the installation of pavers is hand installation of each paver. The operator of the brick saw must constantly cut the pavers away from the surface area of the paver field when cutting damp, due to the fact that the pavers will create a slurry that will stain the paver surface. Edging restraints get rid of lateral movement of the pavers and hold the pavers firmly together. When a space in between the pavers and the edging goes beyond 3/8" (10mm), then the area should be filled with cut pavers.

Leave a Reply

Your email address will not be published. Required fields are marked *